Betekenis van:
dead centre

Voorbeeldzinnen

1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2.
2. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:3.4.5.2.
3. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2.
4. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:3.2.4.2.
5. Valve timing2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2.
6. Maximum lift of valves, angles of opening and closing, or timing details of alternative distribution systems, in relation to top dead centre
7. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2. Reference clearances and/or setting ranges (1)2.4.3.
8. Valve timing2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2. Reference clearances and/or setting ranges (1)2.4.3. Variable valve timing system (if applicable and where intake and/or exhaust):2.4.3.1. Type: continuous or on/off2.4.3.2. Cam phase shift angle:2.5. Porting configuration2.5.1.
9. Valve timing2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2. Reference clearances and/or setting ranges (1)2.4.3. Variable valve timing system (if applicable and where intake and/or exhaust):2.4.3.1. Type: continuous or on/off2.4.3.2. Cam phase shift angle:2.5. Porting configuration2.5.1. Position, size and number:2.6. Electronic control functionsIf the engine features electronically controlled functions, the information concerning their performance must be provided including:2.6.1. Make:2.6.2. Type:2.6.3. Part Number:2.6.4. Location of engine electronic control unit:2.6.4.1. What does it sense:2.6.4.2. What does it control:SECTION 3 COMPRESSION-IGNITION ENGINE FAMILY3.
10. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1.
11. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1. Position, size and number:4.6. Electronic command functionsIf the engine features electronically controlled functions, information concerning their performance must be provided including:4.6.1. Make:4.6.2. Type:4.6.3. Part number:4.6.4. Location of engine electronic control unit:4.6.4.1. What does it sense:4.6.4.2. What does it control: ’;
12. Fuel feed3.2.3.1. Feed pumpPressure (2) or characteristic diagram: kPa3.2.3.2. Injection system3.2.3.2.1. Pump3.2.3.2.1.1. Make(s):3.2.3.2.1.2. Type(s):3.2.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated) and r/min (maximum torque), respectively, or characteristic diagramState which method is used: on engine/on pump bench (1)3.2.3.2.1.4. Injection advance3.2.3.2.1.4.1. Injection advance curve (2):3.2.3.2.1.4.2. Timing (2):3.2.3.2.2. Injection piping3.2.3.2.2.1. Length: mm3.2.3.2.2.2. Internal diameter: mm3.2.3.2.3. Injector(s)3.2.3.2.3.1. Make(s):3.2.3.2.3.2. Type(s):3.2.3.2.3.3. Opening pressure (2) or characteristic diagram:3.2.3.2.4. Governor3.2.3.2.4.1. Make(s):3.2.3.2.4.2. Type(s):3.2.3.2.4.3. Speed at which cut-off starts under full load (2): r/min3.2.3.2.4.4. Maximum no-load speed (2): r/min3.2.3.2.4.5. Idling speed (2): r/min3.2.3.3Cold-start system3.2.3.3.1. Make(s):3.2.3.3.2. Type(s):3.2.3.3.3. Description:3.2.4. Valve timing3.2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:3.2.4.2. Reference clearances and/or setting ranges (1)